Forms high strength conductive bonds
This two part silver epoxy offers high electrical conductivity and strong conductive bonding. Use in place of traditional soldering on heat sensitive components. Good for repairing defective traces and creating jumpers on boards. Can be used as an effective heat sink adhesive. This Conductive Silver Epoxy comes in two 7g syringes.
This epoxy adhesive can adhere not only on most of the metal surfaces (aluminium, bronze, brass, copper, steel etc.) but it can also well adheres on glass, wood, plastic, paper, fiber & rubber surfaces as well.
| Specification |
Test Method |
Result |
| Mechanical Properties |
| Tensile Strength |
ASTM-D-638-02A |
911 psi |
| Elongation |
ASTM-D-638-02A |
0.3 % |
| Compressive Strength |
ASTM-D-695-02A |
1100 psi |
| Flexural Strength |
ASTM-D-790-03 |
2,500 psi |
| Shear Strength |
ASTM-D-732-02 |
234 psi |
| Cantilever Beam (IZOD) Impact |
ASTM-D-256-02 E1 |
0.39 ft lb ft / inyes |
| Electrical Properties |
| Volume Resistivity @ 25°C |
MIL-STD-883E Notice 3, method 5011.4, paragraphs 3.5.8, 3.8.11.1 (Covered Under A2LA Accreditiation) |
0.38 ohm · cm |
Electrical Resistance
(in ohms) |
|
|
| Sample size |
|
3mm x 3mm x 1mm |
| Base material |
|
Plastic cap |
| Results: |
|
|
| Uncured material |
|
no reading |
Heat cured
(at 65°C for 15 minutes) |
|
0.8 ohms |
Air cured
(at room temp. for 5 hours) |
|
0.2 ohms |
Electrical Resistance
(in ohms) |
|
|
| Sample size |
|
30mm x 25mm x 1mm |
| Base material |
|
Fiber glass epoxy |
| Results: |
|
no reading |
| Uncured material |
|
no reading |
Heat cured
(at 65°C for 15 minutes) |
|
2.5 ohms |
Air cured
(at room temp. for 5 hours) |
|
4.0 - 6.0 ohms |
| Thermal Properties |
| Thermal Expansion |
ASTM-E-831-03
|
79.3 mm/106mm |
| Thermal Conductivity |
ASTM-C-518 |
0.578 W/m · °K |
| Glass Transition Temperature |
ASTM-D-3418 |
46 °C |
| Cure Schedule |
| Air Cure @ 24°C (75°F) |
|
4 - 5 hours |
Heat Cure:
65°C / 149°F
90°C / 194°F
125°C / 257°F
150°C / 302°F |
|
15 minutes
12 minutes
7 minutes
5 minutes |
| Working Time @ 22°C |
|
10 minutes |
| Minimum Operating Temp. |
|
-30 °C ( -22 °F ) |
| Maximum Operating Temp. |
|
150 °C ( 302 °F ) |
| General Specifications |
| Mixing Ratio |
|
1:1 |
| Density |
ASTM-D-256-02 E1 |
2.34 g/cm3 |
| Color (cured material) |
|
Silver Grey |
| Outgassing Properties |
| TML (Total Mass Loss) in % |
WVR ( Water vapour Regain) in %
|
Collected Volatile Condensable Material (CVCM) in % |
| 0.06 |
0.06 |
0.1 |
|
View Material Safety Data Sheet 8331A
View Material Safety Data Sheet 8331B
MG Chemicals RoHS Statement
